How much power can 28 spline axles handle?

By Category: How

How much power can 28 spline axles handle?

In all reality the 8.5 10 bolt with stock 28 spline axles is just as strong as a 12 bolt unless you are at the drag strip leaving the line at 3500-4000 Rpm with slicks. Neither rear end likes that too much. But you should be fine for what you’re doing.2010-03-29

How much horsepower can a 31-spline axle hold?

A 30-spline axle is rated at 6,200 lb-ft, a 31-spline at 7,000, a 33-spline at 8,200, a 35-spline at 9,600, and a 40-spline at 12,000.2009-05-01

How do I know if I have a Dana 44 HD?

if it has 8 lugs it is a HD if it has 5 it is a regular 44, they are not reverse rotation they are reverse cut becuase of the high pinion, the gears you want are dana 44 reverse cut. the only differnce between the axles is that they are close nuckle, thicker axle tubes and 8lug.2006-02-15

Are more splines on an axle better?

Higher spline counts gives the axle more surface to transfer the load of the torque from the differential. There is also the side advantage that an axle with more splines will also be physically bigger. At least in most modern axles that use similarly sized spline teeth.

What did Dana 44 axles come in?

The Dana 44 has seen use in Chevrolet Corvettes and Dodge Vipers. This axle is referred to as a Dana 44 ICA or Dana 44 IRS. All 1980–1982 Chevrolet Corvette C3 and manual transmission equipped 1985–1996 Chevrolet Corvette C4 had this axle.

How many splines does a Dana 44 have?

Starting in 1972, modern factory Dana 44s had 30-spine axleshafts with a thickness of 1.31 inches (earlier axles were 10- or 19-spline), although the rear next-generation Dana 44 found on the 2007-present Jeep Wrangler JK has 32-spline shafts.2010-07-01

READ  How do you add garlic to sauce?

How many spline is a Ford 9 inch?

The Ford 9” was produced with 28 and 31 spline axles that even in their smallest form, are larger in diameter than those in the 10-bolt Chevrolet rear axle.

Can I use anti seize on axle?

Anti-seize is basically a type of grease and that is all. Use anti-seize or grease is fine.2010-05-12

What’s the difference between 28 spline and 31 spline?

A 28 spline axle will have a recess in the middle while a 31 spline axle will be solid with just a centering champher (from when it was machined and ground at the factory).2002-03-13

Should I use anti-seize on axle nut?

Is it a good idea? Yes, but derate the axle nut torque by about 20%. If you don’t have a torque wrench, buy one. I’d recommend nickel antiseize, just because you can use it anywhere on a bike.2017-07-19

What spline is a Ford 9-inch?

Ford 9-inch third members come with three common carrier bearing sizes, which include 2.892-inch (28-spline), 3.062-inch (31- and 33-spline), and 3.250-inch (35- and 40-spline). Larger race versions up to 3.812-inch are available for Trophy Truck applications with 40-spline axleshafts.2015-10-05

What Dana 44 do I have?

Stamped Number on the Axle To figure out exactly what axle you have, you can look for the Dana stamped bill of materials number. This stamped number can usually be found on the righthand side or on the longer axletube on the same side of the tube as the differential cover, facing the rear of the truck.2020-03-23

Should I Grease axle splines?

When installing a CV shaft into a bearing hub assembly, we don’t recommend using any lubricant at all. Instead, just clean the shaft really well with a wire brush and make sure there’s no dirt or debris on the shaft or in the hub.

READ  How much is a 2-door Audi?

What is the difference between a Dana 44 and a Dana 44 HD?

The HD axles have wider pinion and ring gears, which are typically the weak spot on dana 44 axles. What it doesn’t say on jeep’s site is that the rear axle on a rubicon is also a dana 44 hd, whereas the sport and sahara have the regular dana 44 housing with 30 spline axles. The HD setup has 32 spline axles.2014-01-20

Do you put anti seize on axle splines?

Lubricate the C-clamp with gear oil. 2. Cover the threads with anti-seize but avoid the splines at the wheel ends of the axle.2019-09-11

What is a high pinion Dana 44?

High pinion means the pinion is above the center line of the ring gear and the way the gears are cut they drive on the drive side of the gear insted of the coast side making them stronger. The XJ high pinion D30 front axle is a bolt in swap for a TJ they never had a D44 front.2020-10-03

How many splines does a Ford 8 inch rear end have?

Re: Ford 8in rear end with 31 spline axle shafts The 8″ rear end is generally thought to be good up to 300 horsepower and 400lbs of torque.2020-01-15

Used Resourses: